If you’re experiencing a “DStv no signal error”, popularly known as the E48-32 Error: There is no signal. This may be die to bad weather or a faulty connection in the installation on your DStv decoder, then this article is for you. The problem is usually caused by a faulty LNB, a misaligned satellite dish, loose connections, and bad weather. To ascertain the exact cause of the DStv No Signal Error on your Decoder, a DStv Technician will have to to your premises and have a look at your existing DStv installation.
In this article, I will show you what you can do when your DStv decoder loses signal. But first, let’s discuss the major causes of DStv signal loss.
In fact, the majority of DStv signal problems are caused by bad weather elements and faulty DStv accessories. Signal problems make your DStv decoder to display the E48-32 Error message.
What causes your DStv decoder to lose signal?
If your decoder resets itself to default factory settings then you can also lose your DStv signal. This is because when your decoder resets, it uses the default LNB type settings which may not be appropriate for your decoder.
See how you can improve your DStv signal strength and quality.
Why Your DStv Says No Signal
The reason your DStv says no signal is because there is an error in the DStv installation. This is caused by either a misaligned satellite dish, a faulty LNB, an improperly connected F-connector plug, loose cables or incorrect decoder settings on the LNB type. Incorrect decoder settings can be fixed by resetting your decoder to factory defaults as shown in the video below.
How to reset your decoder
In most cases, the problem is not as complicated as you may think. So, before you call any accredited DStv installer and spend a lot of money, try out these easy tips.
These tips will help you restore your DStv signal back. Who knows, you can end up saving money and time. In addition, you will also have an idea of where the actual problem is.
Remember there are dishonest installers out there who would want to empty your pockets. So, be wary.
What to do when DStv says no signal?
In order to solve your DStv signal problem, you need to pinpoint the exact issue. You don’t need to be very technical to follow these simple steps.
It is advisable to first check the values of your DStv signal strength and quality before following these steps.
This enables you to find a solution quickly. If you don’t know how to check the signal strength then you can watch the video below.
Good signal strength is usually above 75% for both Explora and normal HD decoders. Read my article on how you can improve your signal strength and quality if your DStv signal strength is less than 50%. If your strength and quality are both -1% then it means there is no signal that is coming from the satellite dish to your decoder.
How Do I Manually Set My DStv Signal?
Fix a DStv no signal error by following the steps below:
Step 1: Check your DStv connection cables
This is one of the easiest checks you can do on your own. Firstly, inspect all the DStv cables at the back of your decoder. Then, check for any loose DStv cables. Make sure that all F-types connectors are connected correctly. If you don’t know how to connect the F-type connectors then you can watch the video below.
How to connect F-type connectors on a DStv coaxial cable
In fact, make sure all cables are connected to the correct ports on the decoder. Remember kids, dogs and cats can pull your DStv cables at the back of your decoder.
If you find any loose cables then plug them back onto the DStv decoder. Just make sure that you plug in the signal cable on the right port (LNB-in and Unicable-in).
Step 2: Reboot your decoder
Believe it or not, rebooting your decoder can solve multiple problems such as freezing pictures and decoder errors.
So, why not try it out! Reboot your decoder by pressing the power button for more than 10 seconds. Remember, rebooting your decoder may take a while. So, be patient! If this does not solve your problem, then proceed to the next step.
Step 3: Inspect your DStv satellite dish
Visually inspect your satellite dish for a broken arm and rust. Rust affects most satellite dishes in coastal areas that are made out of galvanized iron.
Also, make sure that the bolts on the satellite dish are tight. Your dish should not move freely when you try to turn it. Otherwise, strong winds can easily put your dish out of alignment. If the dish is freely moving then realign the satellite dish and then tighten the bolts.
You will need a signal detector to realign your dish. Although you might not know how to align your satellite dish yourself, at least, you will know the source of your signal problem.
How Do I Get My Signal Back?
Step 4: Check your LNB
There are silver metallic nuts that you find at the end of your DStv cables. These nuts which connect your DStv cables to the LNB. They are known as F-connectors. So, make sure they are connected properly on the LNB.
Sometimes they rust or become loose. Also, check for any damages on the LNB. If your LNB is faulty then you need to replace it to restore the DStv signal. Remember, you also need to align the LNB correctly by tilting it up and down.
Step 5: Call the approved DStv installer
Have you have tried all the tips above without any success? If that is so then maybe it is time to call an accredited DStv installer in your area. In fact, the DStv technician will perform some advanced diagnostics to identify the problem.
You can also chat with our consultants on WhatsApp by clicking on the button below.
